For testing pul-lifts, lever hoists, chain blocks, wire rope pullers as well as other lifting equipment after repair or inspection.<\/p>\n
Testing of hoisting equipment
\nThe lifting unit is placed between upper and lower shackle, the chain is tensioned against the oil cushion of the partly advanced piston of the hydraulic cylinder. The applied force can be read at the pressure gauge.<\/p>\n
Testing of the hoist brake
\nFor a functional test of the hoist brake the hand pump may be used to apply a counter pressure and thus increase the pulling force after a general test.<\/p>\n
Frequent use
\nFor frequent testing, the hand pump may be replaced by a low-cost air hydraulic (model PAY-6) or electric pump (model PY-04\/2\/5\/2 M.<\/p>\n
Pressure gauge
\nTo read pulling forces more easily, the test rig is equipped with two high-quality pressure gauges.
\nQuick couplers allow an easy replacement of pressure gauges.
\nPressure gauge 1 for small test items: GGY-1005, display: 0 – 160\u2009bar, \u00d8 100\u2009mm, Kl. 1.0\u2009%%
\nPressure gauge 2 for big test items: GGY-1003, display: 0 – 400\u2009bar, \u00d8 100\u2009mm, Kl. 1.0\u2009%<\/p>\n
AYP-1215-S Test plate for permanent load lifting magnets
\nTest load max. 12 t
\nFor testing of permanent load lifting magnets according to DIN EN 13155
\nThe plate is placed into the 12\u2009ton test rig RPYS-1215 (or other versions of this test rig) and connected to the frame with a bolt.
\nThe test plate with a standardised surface according to DIN EN 13155 kann be adjusted horizontally to align it steadily.
\nDimensions: 800 x 490 x 60\u2009mm<\/p>\n
Features
\n\u2022 Fully welded, low-strain press-frame.
\n\u2022 Upper and lower hook suspension by means of shackles, incl. two 5\u2009tons pull-rings for smaller test units.
\n\u2022 Lateral pump table.
\n\u2022 Infinite adjustment of the pulling force.
\n\u2022 Chart for easy determination of test force.
\n\u2022 Removable lower suspension e.g. for testing of plate clamps.
\n\u2022 Base pre-drilled for mounting.
\n\u2022 High-quality hydraulic components.
\n\u2022 YCS-21\/150 hollow cylinder made from chromium-molybdenum steel, heat-treated and hard chromium-plated. Long cylinder stroke of 150\u2009mm with bronze bearings.
\n\u2022 Two-stage quick action hand pump HPS-2\/0,7A.
\n\u2022 High-strength threaded bar M27.
\n\u2022 Fine-adjustment pressure valve.<\/p>\n","protected":false},"excerpt":{"rendered":"
For testing pul-lifts, lever hoists, chain blocks, wire rope pullers as well as other lifting equipment after repair or inspection.<\/p>\n
Testing of hoisting equipment
\nThe lifting unit is placed between upper and lower shackle, the chain is tensioned against the oil cushion of the partly advanced piston of the hydraulic cylinder. The applied force can be read at the pressure gauge.<\/p>\n
Testing of the hoist brake
\nFor a functional test of the hoist brake the hand pump may be used to apply a counter pressure and thus increase the pulling force after a general test.<\/p>\n
Frequent use
\nFor frequent testing, the hand pump may be replaced by a low-cost air hydraulic (model PAY-6) or electric pump (model PY-04\/2\/5\/2 M.<\/p>\n
Pressure gauge
\nTo read pulling forces more easily, the test rig is equipped with two high-quality pressure gauges.
\nQuick couplers allow an easy replacement of pressure gauges.
\nPressure gauge 1 for small test items: GGY-1005, display: 0 – 160\u2009bar, \u00d8 100\u2009mm, Kl. 1.0\u2009%%
\nPressure gauge 2 for big test items: GGY-1003, display: 0 – 400\u2009bar, \u00d8 100\u2009mm, Kl. 1.0\u2009%<\/p>\n
AYP-1215-S Test plate for permanent load lifting magnets
\nTest load max. 12 t
\nFor testing of permanent load lifting magnets according to DIN EN 13155
\nThe plate is placed into the 12\u2009ton test rig RPYS-1215 (or other versions of this test rig) and connected to the frame with a bolt.
\nThe test plate with a standardised surface according to DIN EN 13155 kann be adjusted horizontally to align it steadily.
\nDimensions: 800 x 490 x 60\u2009mm<\/p>\n
Features
\n\u2022 Fully welded, low-strain press-frame.
\n\u2022 Upper and lower hook suspension by means of shackles, incl. two 5\u2009tons pull-rings for smaller test units.
\n\u2022 Lateral pump table.
\n\u2022 Infinite adjustment of the pulling force.
\n\u2022 Chart for easy determination of test force.
\n\u2022 Removable lower suspension e.g. for testing of plate clamps.
\n\u2022 Base pre-drilled for mounting.
\n\u2022 High-quality hydraulic components.
\n\u2022 YCS-21\/150 hollow cylinder made from chromium-molybdenum steel, heat-treated and hard chromium-plated. Long cylinder stroke of 150\u2009mm with bronze bearings.
\n\u2022 Two-stage quick action hand pump HPS-2\/0,7A.
\n\u2022 High-strength threaded bar M27.
\n\u2022 Fine-adjustment pressure valve.<\/p>\n","protected":false},"featured_media":23393,"template":"","meta":{"_acf_changed":false,"inline_featured_image":false},"product_brand":[],"product_cat":[352,1607],"product_tag":[470],"class_list":{"0":"post-24332","1":"product","2":"type-product","3":"status-publish","4":"has-post-thumbnail","6":"product_cat-hoists","7":"product_cat-workshop-tools","8":"product_tag-yale","9":"product_shipping_class-6-en","11":"first","12":"onbackorder","13":"taxable","14":"shipping-taxable","15":"purchasable","16":"product-type-simple"},"acf":[],"yoast_head":"\n